Keyence LS-7000 Manual de usuario Pagina 180
- Pagina / 192
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
9-4
Chapter 9 Troubleshooting
9
Check that the cover glass of the transmitter
or receiver is free of dust and dirt.
Remove the dirt and dust from the
cover glass. (See page 3)
Check that the target is within the
measuring area.
Locate the target correctly in the
measuring area. (See page 8-4, 8-5)
Check that the target is not leaned or
shifted.
Locate the target correctly in the
measuring area. (See page 8-4, 8-5)
Check that the transmitter and
receiver are mounted correctly.
Mount the transmitter and receiver
correctly. (See page 1-11)
Check that the measured value is
correctly calibrated.
Make the right calibration setting.
(See page 4-20)
Check that the operating environment
has no radical temperature change.
Maintain a constant operating ambient
temperature. (See page 8-2, 8-3)
Check that the LED light source is
intensive enough.
Use the LED inspection function and check
the strength of light. (See page 5-10)
Check that the P-SELECT setting is
correct.
Make the right P-SELECT setting according
to the change method. (See page 5-5)
Check that the panel lock is not ON. Set the panel lock to OFF.
(See page 3-7)
Check that the panel lock is not ON. Set the panel lock to OFF.
(See page 3-7)
Check that the LS-7000 Series is
wired correctly.
Check the output circuit and wiring.
Connect the cables correctly.
Check that the tolerance setting is
correct.
Make the right tolerance setting.
(See page 4-50)
Check that the I/O mode for OUT2 is
correctly set.
Select the SUB mode. (See page 4-59)
Check that the LS-7000 Series is
wired correctly.
Check the output circuit and wiring.
Connect the cables correctly.
The voltage is set to +10.5 V or
–10.5 V.
Set the analog scale correctly
according to the measured value.
The
measured
value
displayed
drifts.
The
program
number
cannot be
changed.
Key input is
not possible.
Comparator
output does
not turn ON.
Analog
output does
not turn ON.
Problem Inspection Remedy
- LS-7000 Series 1
- General precautions 2
- Safety Precautions 3
- ■ Precautions for LED 5
- Ferrite core 6
- OP-31973 6
- About this Manual 7
- Optimum Measurement Methods 8
- Configuration of Manual 9
- LS-7001 Operation Map 10
- Hold function (See page 3-5) 11
- Contents 12
- Chapter 4 Function Settings 13
- Chapter 7 RS-232C 14
- Chapter 8 Specifications 14
- Chapter 9 Troubleshooting 14
- Appendix 14
- Chapter 1 15
- ■ Special Features 16
- ■ Principle of Measurement 16
- System Applications 17
- Package Checks 18
- Chapter 1 Getting Started 19
- Functions and Nomenclature 21
- ■ Control Panel 22
- Mounting and Connection 25
- 2 Mount the measuring head 26
- Mounting the Controller 27
- ■ Mounting to Panel 28
- Connection 31
- ■ Transmitter and Receiver 32
- ■ Power Supply Cable 32
- Supply Stand On and Off 33
- Measurement and 33
- Chapter 2 37
- Set value 38
- Measurement of Pitch 44
- Chapter 3 45
- Chapter 3 Operation Control 46
- Chapter 3 Operation Control 47
- Area Monitor 48
- Hold Function 49
- Automatic Zero Function 50
- Panel Lock Function 51
- Program Changes 52
- Chapter 4 53
- Flow of Program Settings 54
- External I/O 55
- Output Settings 55
- Measuring Mode Settings 55
- Option Settings 55
- ■ Program Initialization 58
- (See page 4-15) 60
- (See page 4-16) 60
- (See page 4-17) 60
- (See page 4-18) 60
- (See page 4-14) 60
- Area Selection 61
- ■ SEG (Segment) 62
- ■ Setting Procedure 64
- DIA (Diameter) 65
- T-EDGE (Top edge) 65
- B-EDGE (Bottom edge) 65
- SEG (Segment) 65
- 6 Press the 69
- Calibration Settings 72
- 5 Press the 77
- Measuring mode 85
- Analog Output Settings 96
- ■ Analog update mode 98
- Comparator Output Setting 99
- (Normally open) 100
- (Normally closed) 100
- 1 Press the 101
- 2 Press the 101
- 4 Press the 101
- Tolerance (LIMIT) Settings 102
- Limit Settings 103
- Hold Value Elimination 104
- 1 Continue pressing the 105
- Chapter 4 Function Settings 107
- 3 Press the 108
- Display Unit 109
- I/O Mode 111
- Chapter 5 115
- Possible Environment Settings 116
- This part changes 118
- ■ Resetting All Programs 120
- ■ RS-232C Settings 121
- ■ Baud Rate 121
- ■ Parity 121
- ■ Stop Bit 122
- ■ Data Length 122
- ■ Data Mode 122
- ■ Data Transmission Mode 123
- The buzzer turns ON 126
- The buzzer turns OFF 126
- Chapter 6 129
- Connector I/O 130
- Terminal block 130
- Chapter 6 I/O Terminals 131
- Chapter 6 I/O Terminals 134
- ZERO Input 6-3, 6-5, 6-6 135
- ■ FUNCTION Output 136
- Electrical Specifications 137
- ■ NPN Open Collector Output 2 138
- ■ Analog Voltage Output 138
- Timing Chart 139
- ■ Sample Hold 2 140
- ■ Self-timing Hold 140
- ■ BCD Output Switching 141
- ■ Minimum Input Period 142
- Chapter 7 143
- Specifications 144
- ■ RS-232C Connection Settings 145
- ■ Environment Settings 146
- Connecting to KV Series 147
- Outline of Command Formats 148
- Measurement Serial Commands 149
- Commands in Detail 150
- ■ Measured Value Output 150
- Chapter 7 RS-232C 151
- Response 153
- Setup Serial Commands 154
- ■ Area Check 156
- ■ Calculation 156
- ■ Average 156
- (Page 7-15) 161
- Batch Commands 162
- ASCII Table 164
- ■ Output 165
- TIMING input 166
- Sampling period + 3.5 ms 166
- RS-232C data output 166
- Chapter 8 167
- Measuring Head 169
- Optional Accessories 169
- Characteristics 170
- Temperature Characteristics 171
- ■ Measurement Response Time 172
- Mode Specifications 173
- External Dimensions 174
- ■ LS-7030 Measuring Head 175
- ■ LS-7070 Measuring Head 175
- ■ Extension Cable 176
- Chapter 9 177
- Troubleshooting Guide 178
- Chapter 9 Troubleshooting 179
- 2 Continue pressing the 182
- Appendix-2 183
- Appendix-3 183
- Appendix-5 183
- Setting Record Sheet 185
- Threshold 186
- WARRANTIES AND DISCLAIMERS 191
Comentarios a estos manuales
Relacionado con productos y manuales para Sensores Keyence LS-7000
Sensores Keyence LS-7600 Manual de usuario
(220 paginas)
(220 paginas)
Sensores Keyence LS-Navigator Manual de usuario
(68 paginas)
(68 paginas)
Sensores Keyence LS-5000 Manual de usuario
(132 paginas)
(132 paginas)
Sensores Keyence LS-3100/3100W Series Manual de usuario
(104 paginas)
(104 paginas)
Sensores Keyence GP-M Series Manual de usuario
(28 paginas)
(28 paginas)
Sensores Keyence GP-M Series Manual de usuario
(1 paginas)
(1 paginas)
Sensores Keyence AP-C30KP Manual de usuario
(5 paginas)
(5 paginas)
Sensores Keyence AP-C30WP Manual de usuario
(5 paginas)
(5 paginas)
Sensores Keyence AP-V42A(P) Manual de usuario
(5 paginas)
(5 paginas)
Sensores Keyence AP-V42AW(P) Manual de usuario
(5 paginas)
(5 paginas)
Sensores Keyence AP-40A Series Manual de usuario
(5 paginas)
(5 paginas)
Sensores Keyence AP-40P Manual de usuario
(5 paginas)
(5 paginas)
Sensores Keyence AP-30 Series Manual de usuario
(4 paginas)
(4 paginas)
Sensores Keyence SK-1000 Series Manual de usuario
(24 paginas)
(24 paginas)
Sensores Keyence DL-CL1 Manual de usuario
(78 paginas)
(78 paginas)
Sensores Keyence SK-H Series Manual de usuario
(12 paginas)
(12 paginas)
Sensores Keyence IV Series Manual de usuario
(10 paginas)
(10 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.107 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
ok
Hello