Keyence LT-9001 Series Manual de usuario Pagina 159
- Pagina / 176
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendices
E LT-9001-IM
A-3
Symptom Check point Remedy
Is the unit properly wired? Check the output circuit and wiring and connect
properly.
Judgment cannot be output Is the tolerance properly set up? Perform the tolerance setting again.
properly. ( Page 5-7)
Is the I/O mode properly set up? Select comparator mode for I/O mode.
( Page 5-20)
Is the unit properly wired? Check the wiring and connect properly.
Does the voltage exceed Set the analog scaling appropriately according to
+10.5 V or below -10.5V? the measured value. ( Page 5-15)
Analog output cannot be output Is an oscilloscope or a hi-speed A/D board The resolution may decrease if these devices are
properly. used? used.
Change the analog scaling so that the effect
should be minimized.
Is the I/O mode properly set up? Select binary mode for I/O mode.
( Page 5-20)
Is the unit properly wired? Check the output circuit and wiring and connect
Binary output cannot be output properly.
properly. Is the logic properly set up? Negative logic is used in output.
Is the import timing properly set? Use strobe output to enable importing in proper
timing. ( Page 7-4)
Is BIN SEL input properly input? Input correctly. ( Page 7-4)
Is the communication cable properly Connect the communication cable properly.
connected? ( Page 8-2)
Does the type of the communication cable Check the connection of the communication
conform to the connecting specifications? cable. ( Page 8-2)
Cannot communicate via the Are the communication specifications properly Set the communication specifications of the LT-
RS-232C. set up? 9000 the same as that of the external devices.
( Page 8-2)
Is the appropriate communication program Check whether the commands and the delimiters
used? are properly received or sent. ( Page 8-3)
Is the setting properly set up according to the Set the D-MODE appropriately.
communication method or external devices? ( Page 8-3)
The image of the measurement Is the display mode appropriately set up? Set it up appropriately.
target is not displayed. ( Page 2-12)
Is the remote control console properly Connect the remote control console properly.
The remote control console does connected? ( Page 1-8)
not function. Is Keylock set to ON? Set the Keylock to OFF.
( Page 5-5)
- LT-9001 Series 1
- Introduction 2
- Safety Precautions 3
- Measurement target 5
- Scan straightness 5
- Handling 5
- Effect of atmospheric motions 5
- Precaution on CE Marking 6
- Organization of this Manual 7
- Table of Contents 8
- Chapter 8 RS-232C 10
- Chapter 9 Specifications 10
- Appendices 10
- Outline of the LT-9001 11
- System Configuration 12
- Checking the Package Contents 13
- Controller 14
- Measuring Unit 15
- Remote Control Console 16
- Mounting and Connecting Parts 17
- Connection 18
- Outline of Basic 19
- Operations 19
- Displacement Mode 20
- Profile Mode 20
- Program mode screen 21
- Run mode screen 21
- Run Mode 22
- Program Mode 23
- Program Function 26
- Flow of Measurement 27
- Selecting an Item 29
- Entering a Value 29
- Operational Flow 30
- Using the Displacement Mode 31
- Measuring the Displacement 33
- Using the Profile Mode 34
- Setting the Area 36
- Measuring Height Differences 37
- Measuring 38
- Resetting the Device to the 40
- Factory Settings 40
- Scan center 41
- 1st point/measured value 42
- Offset – 999999 + 999999 0 43
- Scan Width 44
- Outline of Displacement 47
- Display Screens 48
- Measurement Screen 49
- Light Intensity Screen 50
- Pause Screen 55
- SELECT SURFACE 58
- OUT Settings 60
- Scan width 61
- Basic Settings 62
- DARK ALARM 63
- Outline of Profile Mode 67
- Types of Screens 68
- Program mode 68
- Run mode 68
- Display of Profile Waveform 72
- Setting the position 73
- Slant correction 77
- WIDTH/INTERVAL 80
- SMOOTH (Smoothing) 83
- PROF OUT (Profile Output) 85
- Outline of Common Operations 87
- X : 2500 μm 88
- Y : 2000 μm 88
- Hold Function 89
- Auto-zero Function 90
- Keylock Function 91
- Program Change 92
- (Output) 94
- HOLD MODE (Measurement mode) 95
- Upper limit of tolerance 96
- Lower limit of tolerance 96
- Measured value 96
- Judgment 97
- Judgment standby status 97
- OUTPUT Settings 100
- ANALOG output 101
- CALIB (Calibration) 102
- E LT-9001-IM 103
- OPTIONAL Settings 104
- DISPLAY UNIT 105
- GAIN (Sensitivity) 106
- Setting up the Basic 107
- Settings for the Overall Unit 107
- List of Default Values 108
- Environment Setting Items 108
- Beep sound ( page 6-7) 109
- Coefficient ( page 6-7) 109
- RS-232C Interface 111
- Items that can be set 112
- Coefficient 113
- Interface Language 113
- Beep Sound 113
- Controlling and Outputting 115
- Terminal number 116
- Terminal 116
- Control I/O 117
- Functions of the I/O Signals 119
- VIDEO Output 119
- Auto-zero input 120
- Program No. change input 120
- Binary output 121
- Laser remote input 121
- Electrical Specifications 122
- Timing Chart 123
- Timing Details (LT-9010 (M)) 127
- Timing Details (LT-9030 (M)) 128
- Connecting to External 131
- Devices via RS-232C 131
- Specifications 132
- Outline of Command Format 133
- Command Details 135
- Profile waveform data output 136
- Timing ON/OFF 136
- Auto-zero ON/OFF 137
- Program No. change 137
- Keylock ON/OFF 137
- S D , O A , x i 138
- Select surface setting 140
- Change HOLD mode setting 140
- Offset setting 140
- Analog scaling setting 141
- Calibration setting 141
- Area setting 141
- Area range setting 141
- Scan width/interval setting 142
- Scan center position setting 142
- FINE mode 142
- Dark-out setting 142
- Dark-out range setting 143
- Mask setting 143
- Mask range setting 143
- Auto slant correction setting 144
- Gain setting 144
- S R , O F , x 145
- ASCII Code Table (Reference) 146
- Synchronization 147
- Output format 148
- Specifications of the 149
- Status Table 152
- Display Update Cycle 154
- Response Delay Time 154
- Outside Dimensions 155
- Troubleshooting 158
- Error Messages 160
- Optional Product List 161
- Parameter Memo 162
- 0.00 0.00 163
- Profile mode 164
- Revision history 174
- WARRANTIES AND DISCLAIMERS 175
Relacionado con productos y manuales para Sensores Keyence LT-9001 Series
Sensores Keyence CA-MP81 Manual de usuario
(2 paginas)
(2 paginas)
Sensores Keyence TM-3000 Series Manual de usuario
(16 paginas)
(16 paginas)
Sensores Keyence TM-3000 Series Manual de usuario
(84 paginas)
(84 paginas)
Sensores Keyence LS-9030D Manual de usuario
(6 paginas)
(6 paginas)
Sensores Keyence LS-7000 Manual de usuario
(192 paginas)
(192 paginas)
Sensores Keyence LS-7600 Manual de usuario
(220 paginas)
(220 paginas)
Sensores Keyence LS-Navigator Manual de usuario
(68 paginas)
(68 paginas)
Sensores Keyence LS-5000 Manual de usuario
(132 paginas)
(132 paginas)
Sensores Keyence LS-3100/3100W Series Manual de usuario
(104 paginas)
(104 paginas)
Sensores Keyence GP-M Series Manual de usuario
(28 paginas)
(28 paginas)
Sensores Keyence GP-M Series Manual de usuario
(1 paginas)
(1 paginas)
Sensores Keyence AP-C30KP Manual de usuario
(5 paginas)
(5 paginas)
Sensores Keyence AP-C30WP Manual de usuario
(5 paginas)
(5 paginas)
Sensores Keyence AP-V42A(P) Manual de usuario
(5 paginas)
(5 paginas)
Sensores Keyence AP-V42AW(P) Manual de usuario
(5 paginas)
(5 paginas)
Sensores Keyence AP-40A Series Manual de usuario
(5 paginas)
(5 paginas)
Sensores Keyence AP-40P Manual de usuario
(5 paginas)
(5 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.181 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales