Keyence KV Series Manual de usuario Pagina 109
- Pagina / 240
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 3 Simulator
2-85
1
3
■ Special utility relays supported
The table below shows the special utility relays which can be processed by the
simulator.
• Special utility relays
When conventional KV Series is selected:
When Visual KV Series is selected:
■ Reset operation
• Relays are cleared by the MEMSW. All the relays whose latching is not specified
by the MEMSW are cleared.
When clearing all the relays whose latching is specified, perform the following.
"Execute" ➔ "Device All Clear" ➔ "Latching Relay All Clear"
When clearing all the data memory whose latching is specified, perform the
following.
"Execute" ➔ "Device All Clear" ➔ "DM All Clear"
➮
Device all clear (p. 2-108)
• All the temporary data memory (TM00 to TM31) and all the timers are cleared.
• Counters and high-speed counters are cleared according to the MEMSW’s
specification.
• Trimmer status is retained.
Relay No. Function
2002 Always ON
2003 Always OFF
2004 0.01 sec clock pulse (duty = 50%)
2005 0.1 sec clock pulse (duty = 50%)
2006 1.0 sec clock pulse (duty = 50%)
2007 OFF for only one scan when operation is started
2008 ON for only one scan when operation is started
2009 ON when arithmetic result is negative or when overflow occurs (<)
2010 ON when arithmetic result is 0 (=)
2011 ON when arithmetic result is positive (>)
2012 ON when arithmetic error occurs
2206 Selects edge of INT3 (ON: Down edge, OFF: Up edge)
2402/2403: Interrupt polarity of INT0
2402 OFF ON At rising edge OFF At falling edge ON At both edges
2403 OFF OFF ON ON
2404/2405: Interrupt polarity of INT1
2404 OFF ON At rising edge OFF At falling edge ON At both edges
2405 OFF OFF ON ON
2410/2411: Interrupt polarity of INT2
2410 OFF ON At rising edge OFF At falling edge ON At both edges
2411 OFF OFF ON ON
2412/2413: Interrupt polarity of INT3
2412 OFF ON At rising edge OFF At falling edge ON At both edges
2413 OFF OFF ON ON
KVSKA Chap 03.P65 08.3.11, 11:29 AM85
- Support software 1
- Safety Precautions 2
- WARRANTIES AND DISCLAIMERS: 2
- Note to User 3
- )222-1.p("07NUF 7
- How this manual is organized 8
- Programming 9
- Contents 10
- Chapter 3 Simulator 11
- Chapter 4 Monitor 11
- Appendices 12
- Installation 13
- Chapter 6 Handheld Programmer 16
- Chapter 10 Troubleshooting 19
- 3 Programming 20
- Chapter 2 Instructions 21
- WARRANTIES AND DISCLAIMERS 24
- Chapter 1 25
- See page 2-7 26
- Chapter 1 Introduction 27
- 1.3 Before Programming 31
- 1.4 Installing the Software 33
- 1.4.2 Installation procedure 34
- 1.5 Cautions for Use 36
- 1.6 Basic Operations 37
- To start up the software 39
- Change Models 40
- 1.6.3 Screen 41
- Display mode 42
- Show/hide comments 44
- 1.6.5 Online help 45
- Chapter 2 49
- 2.2 Edit Screen 51
- Line No 52
- Step No 52
- Scroll bar 52
- 2.3 File Management 53
- Auto Read 54
- Set Auto Save 55
- Save, File 56
- Save As 56
- Reading files 57
- Other Format 58
- Read Other File Comment 58
- 2.3.7 Verifying files 60
- 2.4.1 Entering symbols 61
- Symbol Input 62
- Symbol Selective Input (Tab) 62
- Relay 2008 64
- Symbol Direct Input (Enter) 65
- 2.4.2 Deleting symbols 66
- Entering coils 67
- Entering connection lines 68
- Deleting connection lines 69
- Comment 70
- Selecting the range (p. 2-52) 72
- Radio buttons 72
- Display mode (p. 2-19) 73
- Selecting the range (p.2-52) 75
- 2.6 Edit and Arrangement 76
- Copy/move/delete operation 78
- Step 3 on page 2-56 78
- Inserting blank lines 81
- Deleting lines 81
- Line/Step No 82
- Jump to the first/last line 83
- Jump to the registered line 83
- Find (Ctrl + F) 86
- Replace Operand (Ctrl + R) 88
- 2.7.5 Converting a/b contacts 89
- Edit List 91
- Terminating a mnemonic list 92
- Format of a mnemonic list 92
- 2.8.2 Copy, move, and delete 93
- Usage Information 94
- System Settings 95
- 2.11.1 Creating a macro file 96
- What are temporary devices? 97
- Macro Input 98
- Develop (Shift + F1) 98
- Compile 99
- Compile (Ctrl + F9) 99
- 2.12.2 Error display 100
- 2.12.3 Double coil check 100
- Print (Ctrl + P) 101
- Chapter 2 Editor 102
- File (F) 105
- Print Preview (V) 105
- Change Ladder Diagram Color 106
- Chapter 3 107
- Chapter 3 Simulator 108
- Device all clear (p. 2-108) 109
- Simulator (Ctrl + F2) 110
- Editor (Ctrl + F1) 111
- Sample screen 112
- Ladder Monitor 113
- Ladder monitor window 114
- Step No. being executed 115
- Operation mode being executed 115
- Scan time 115
- Execute 116
- Execute Continuous Scan (F5) 116
- Execute One Scan (F9) 117
- 0000 0000 118
- Setting break conditions 122
- Setting the scan time 124
- Setting the watch dog timer 124
- 3.3.3 Executing steps 125
- Executing a step once 126
- Jump in Ladder Monitor 129
- Search in Ladder Monitor 130
- Cross reference search 131
- Device all clear 132
- Monitor All 133
- Reading the monitor all file 135
- Monitor All 137
- Selecting devices 140
- Turning on/off bit devices 141
- Resetting devices 142
- Registration Monitor 143
- Save Window As 144
- Open Window 145
- 3.5.4 Registering devices 146
- Turning on/off the bit device 148
- Right-click (Copy Attribute) 149
- Moving devices 150
- Deleting devices 151
- Sorting devices 151
- Before deletion 151
- After deletion 151
- Settings 153
- Wait Time 154
- Print Preview 155
- Executing printout 156
- Chapter 4 157
- Chapter 4 Monitor 158
- p. 2-136 159
- Setting the serial port 160
- Set Machine Number 161
- Communication Setup 162
- Set Comment Transfer 162
- Transferring programs 163
- Reading programs 165
- Exit procedure 166
- 4.4.4 Starting the monitor 169
- 4.4.5 Stopping the monitor 169
- Status indication 170
- Operation (RUN mode) 171
- Stop (STOP mode) 171
- 4.6 Monitor Function 173
- Change All 174
- Reading devices from the PLC 175
- Writing devices to the PLC 175
- Saving/reading devices 175
- 4.6.3 Device all clear 178
- Appendix A Error Message List 180
- A-3 File errors 181
- A-4 Installation errors 181
- A-8 PLC errors 184
- Appendix B Instruction List 187
- B-2 Application instructions 188
- B-3 Arithmetic instructions 189
- B-4 Interrupt instructions 190
- Appendix C Relay No. List 191
- D-5 Memory switches 196
- D-6 Special memory list 196
- E-1 Special utility relays 198
- E-2 Memory switches 200
- E-3 Special memory list 200
- Appendix G Quick Reference 204
- G-2 Simulator 212
- G-3 Monitor 219
- Appendix I List of Files Used 228
Comentarios a estos manuales
Relacionado con productos y manuales para Sensores Keyence KV Series
Sensores Keyence KV-D20 Manual de usuario
(72 paginas)
(72 paginas)
Sensores Keyence Visual KV Series Manual de usuario
(444 paginas)
(444 paginas)
Sensores Keyence Visual KV Series Manual de usuario
(392 paginas)
(392 paginas)
Sensores Keyence MS-F07 Manual de usuario
(2 paginas)
(2 paginas)
Sensores Keyence MS2 Series Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Hi