Keyence DL-RS1A/IL Manual de usuario descargar pdf (Pagina 13)

Parameters of Commands and Responses

 Data numbers

Specify the data number using three digits (ASCII characters).

z Read-only data

The following table lists the types of data that can only be read from the IL Series sensor amplifiers.

Writing read-only data results in a communication error (error number: 22).

*1 In the Data format column, "±" indicates that the value can be either "+" or "-" and "*" signifies a

number from "0 to 9". The values shown in parentheses apply for the IL-300/600, and the values

shown in double parentheses apply for the IL-2000.

*2 R: Indicates that the data type can only be read from the sensor amplifiers.

Data

number

Data name

Data

type

Number of

characters

Attribute

Readout range

*15

033 Sensor amplifier error

***** 5 R 0 to 65535

036 Judgment output/Alarm output

** 2 R 0 to 15

037 Judgment value (P.V. value)

±**.***

(±***.**)

((±****.*))

-99.999 to +99.999

(-999.99 to +999.99)

((-9999.9 to +9999.9))

038 Internal measurement value (R.V. value)

039 Peak hold value during hold period

040 Bottom hold value during hold period

041 Calculation value (CALC value)

*5 *6

042 Analog output value

±*.***

**.**

Voltage output

Current output

Voltage output

-5.000 to +5.000

Current output

04.00 to 20.00

043 Bank status * 1 R 0 to 3

044 Timing status * 1 R

0: During sampling

1: Not during sampling

050 Laser emission stop state * 1 R

0: Laser emitting

1: Laser stopped

051 Abnormal setting

*1 R

0: Normal setting

1: Abnormal setting

052 External input status ** 2 R 0 to 15

*14

053 EEPROM write result

*12

*1 R

0: Executing

1: Normal termination

2: Execution impossible

054 Zero shift/Zero shift reset result

*1 R

0: Executing

1: Normal termination

2: Execution impossible

055 Reset request result * 1 R

0: Executing

1: Normal termination

2: Execution impossible

056 Current system parameters

*13

** 2 R 0 to 15

060 Tolerance tuning/2 point tuning result

*10

*1 R

0: Executing

1: Normal termination

2: Execution impossible

061 Calibration result

*11

*1 R

0: Executing

1: Normal termination

2: Execution impossible

193 Product code **** 4 R

Main unit: 4022

Exp. units: 4023

195 Connected sensor head **** 4 R

0000: No connection

0001: IL-030

0002: IL-065

0003: IL-100

0004: IL-300

0005: IL-600

0106: IL-S025

0107: IL-S065

0208: IL-S100

0311: IL-2000

Point

Parameters of Commands and Responses

*3 You can read data number "033" to check the error status of the sensor amplifiers. Convert the

five digit number (ASCII characters) read from the sensor amplifiers to a binary number and

check the ON/OFF state of each bit to check the error.

For information on each error, refer to "IL Series User's Manual"

•

When the data read from a sensor amplifier is "00257":

"257" converted to binary number is "0000 0001 0000 0001".

Therefore, this data indicates that an "Overcurrent error" and a "Model mismatch

error" have simultaneously occurred at the sensor amplifier from which it was read.

•

If no error has occurred at the sensor amplifier, the data "00000" is returned.

*4 You can read data number "036" to check the judgment output status.

Convert the two digit number (ASCII characters) read from the sensor amplifiers to a binary

number and check the ON/OFF state of each bit to check the judgment output status.

When the data read from a sensor amplifier is "05":

"05" converted to binary number is "0101".

During N.O.

Bit Sensor amplifier error details

0 Overcurrent error

1 EEPROM error

2 Sensor head error

3Unused

4Unused

5Unused

6Unused

7 Spot light laser error

8 Incompatable model error

9Unused

10 Unused

11 Amplifier communication error

12 Number of units error

13 Calculation error

Bit

Judgment output

N.O. N.C

0: HIGH Judgment output OFF,

1: HIGH judgment output ON

0: HIGH Judgment output ON,

1: HIGH judgment output OFF

0: LOW Judgment output OFF,

1: LOW Judgment output ON

0: LOW Judgment output ON,

1: LOW Judgment output OFF

0: GO Judgment output OFF,

1: GO Judgment output ON

0: GO Judgment output ON,

1: GO Judgment output OFF

0: Alarm output ON,

1: Alarm output OFF

0: Alarm output ON,

1: Alarm output OFF

Reference

Bit 8: Model mismatch error Bit 0: Overcurrent error

Reference

Bit 3: Alarm output ON Bit 0: HIGH judgment output ON

Bit 2: GO judgment output ON Bit 1: LOW judgment output OFF

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 23 24

Comentarios a estos manuales

Sin comentarios

Keyence DL-RS1A/IL Manual de usuario Pagina 13

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Keyence DL-RS1A/IL