Keyence DL-DN1 Manual de usuario descargar pdf (Pagina 3)

3 Mount the attached end units (OP-26751: a set of two pieces) on both sides of the

sensor amplifier and the DeviceNet Compatible Network Unit DL-DN1, then fix

the end units with screws on the upper part of each end unit (2 points x 2 units).

The mounting method of the end unit is the same as that of the DeviceNet Compatible

Network Unit DL-DN1.

z Connecting to a panel mounting type sensor amplifier

1 Connect the sensor amplifier to the DeviceNet Compatible Network Unit DL-DN1

using the optional expansion cable (OP-35361).

2 Detach the sensor amplifier connector (for DIN rail mounting type) of the

DeviceNet Compatible Network Unit DL-DN1 with pliers and mount the attached

expansion connector sticker.

z Connecting to a large display type sensor amplifier

1 Connect the sensor amplifier to the DeviceNet Compatible Network Unit DL-DN1

using the optional expansion cable (OP-35361).

2 Detach the sensor amplifier connector (for DIN rail mounting type) of the

DeviceNet Compatible Network Unit DL-DN1 with pliers and mount the attached

expansion connector sticker.

Wiring

Use the following procedures to wire the DL-DN1.

Refer also to the DeviceNet Installation Manual published by ODVA.

 Connecting to DeviceNet

Use the following procedure to connect the DL-DN1 to the DeviceNet.

z Recommended Cables

For connection between the DL-DN1 and the DeviceNet, use DeviceNet cables conform-

ing to the DeviceNet specifications or dedicated flat cables.

z Trimming the Cable

1 Strip the cable sheath.

Strip approximately 70 mm of cable sheath.

Make sure that the bare part of the shield braid is 6 mm or shorter.

2 Install shrinkable tube.

Cover the exposed sheathed conductors and the sheath using a shrinkable tube

approximately 40 mm long.

3 Strip the sheathed conductors.

Strip approximately 10 mm of sheath from the end of each conductor.

z Connecting the Cable

Use the following procedures to wire to the DeviceNet connector supplied with the DL-DN1.

1 Connect the trimmed cable to the DeviceNet connector.

Insert the cable completely.

2 Attach the DeviceNet connector to the DL-DN1.

Plug the connector into the DL-DN1 and secure it down with the screws on each end.

(Tightening torque: 0.2 to 0.3 Nm)

Be sure to insert the DeviceNet Compatible Network Unit DL-DN1

to the sensor amplifier to the end. Turning on the power with

diagonal insertion or improper insertion may damage the

equipment.

• Turn OFF the power before connecting the expansion cable

and connect securely. Diagonal or otherwise improper

insertion may damage the equipment.

• Inserting or pulling the cable when the power is turned ON

may damage the equipment.

• Turn OFF the power before connecting the expansion cable

and connect securely. Diagonal or otherwise improper

insertion may damage the equipment.

• Inserting or pulling the cable when the power is turned ON

may damage the equipment.

End unit

NOTICE

Detach the protection sticker

Expansion cable (cable length: 300 mm)

NOTICE

Sensor amplifier connector

(for DIN rail mounting type)

Expansion

connector sticker

Detach the

protection sticker

Detach the

protection

sticker

Expansion cable (cable length:300mm)

NOTICE

Sensor amplifier connector

(for DIN rail mounting type)

Expansion

connector sticker

Turn off the power before wiring.

To ensure normal communication, use only the DeviceNet or

dedicated cables.

• If you are using solderless terminals, perform cable wiring /

trimming appropriately to suit the specifications of the

particular terminals.

Recommended solderless terminals: Phoenix Contact's A/AI

Series

• Do not perform soldering (pre-soldering) on the trimmed

end of the cable.

Point

6 mm or shorter

Approx. 70mm

Shield braid

Sheath

Approx. 40mm

Shrinkable tube

Sheath

Approx. 10mm

Sheathed conductor

Point

Wire color

Signal name

Function

Black

Connects 0 V of the

communication power supply.

Blue CAN_L Communication signal (Low)

Bare wire SHIELD

Connects the shield of the

DeviceNet cable.

White CAN_H Communication signal (High)

Red V+

V-

Connects 24 VDC of the

communication power supply.

Black

Blue

White

Red

1 2 3 4

Comentarios a estos manuales

Sin comentarios

Keyence DL-DN1 Manual de usuario Pagina 3

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Keyence DL-DN1