Keyence N-L1 Manual de usuario descargar pdf (Pagina 2)

E N-L1-IM

• Method of using the RESET/RUN switch

■ Initial settings of the N-L1

When the N-L1 is turned on with the RESET switch set to ON, the initial

settings of the Ethernet is as follows:

■ Connecting the code reader

Connect the code reader to the head port of the N-L1.

Pin layout of the head port

■ Connecting the power supply

Connect the 24 VDC power supply to the power terminal of the N-L1.

The dimensions of crimp contacts used for wiring should be as follows:

■ Layout and Wiring of the I/O Terminal Block

• Layout of the I/O terminal block

Part Names and Functions

Number Name Function

1 Head port Used to connect the head.

2 Power LED Lights when the power is ON.

Communication status

LED

Monitors the status of communication with the

head.

4LINK LED

Lights when the communication with an

Ethernet unit is established.

5 100/10 LED

Lights when there is 100 Mbps

communication. Goes off when there is 10

Mbps communication.

Ethernet connection

port

Used to connect to an Ethernet unit.

7 I/O status LED Monitors the ON/OFF status of I/O terminals.

8 I/O terminal

Used to connect I/O signal lines of control

units.

9 Power terminal Terminal for 24V DC power supply input.

DIN rail mounting tab

A tab for mounting the DIN rail.

11 RESET/RUN switch

A switch for switching the setting/run mode

RESET For setting the N-L1 such as IP addresses, set it to the RESET side.

RUN To switch to the run mode, set it to the RUN side.

IP address 192.168.0.1

Subnet mask 255.255.255.0

Default gateway 0.0.0.0

System Configuration Figure

10. DIN rail mounting tab

11. RESET/RUN switch

1. Head port

2. Power LED

3. Communication

status LED

4. LINK LED

5. 100/10 LED

6. Ethernet

connection port

7. I/O status LED

8. I/O terminals

9. Power terminal

KV-B16XC

Head port

Input

terminal

OUT1 to 4IN1

Head

BL Series

SR Series

Personal

computer

PLC

Timing sensor

Ethernet port

HUB

Connection and Wiring Methods

number

Name Signal name

Signal

direction

1 OUT1 OUT1 input Input

2 OUT2 OUT2 input Input

3 RXD RS-232C Receive Input

4 RTS RS-232C Receivable Output

5 OUT4 OUT4 input Input

6 IN2 IN2 output Output

7 TXD RS-232C Transmit Output

8CTS

RS-232C

Transmittable

Input

9 OUT3 OUT3 input Input

10 IN1 IN1 output Output

11 +5V +5V power supply Output

12 GND(SG) Common GND

CAUTION

Install and remove connection cables with the power

disconnected.

CAUTION

• Using a power supply other than 24 VDC may cause

product failure.

• The N-L1 does not support PoE (Power over Ethernet).

Be sure to supply 24 VDC power to the power terminal.

Terminal Dimensions

Round Terminal a: 6 mm Max.

Y terminal a: 6 mm Max.

Item Description

Wire size AWG14-22

Tightening torque 0.49 N·m (4.34 lbf·in)

Wire material Copper

Wire type Stranded wire

Electric wire

temperature rating

+60°C max.

1 2

11 12

Round 12-pin jack

Power supply

24V+10%

20%

Twist pair cable

I/O terminal

block

1 2 3 4

Comentarios a estos manuales

Sin comentarios

Keyence N-L1 Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Keyence N-L1